Home > Ati Tv > Ati Tv Wonder Pro Windows 7

Ati Tv Wonder Pro Windows 7

Contents

Each new version added new speeds and signaling voltages. Do you think the grounds on these tipes of circuits are shared? The flat plate on the back edge of the circuit board should be a good ground for your voltmeter measurements. #8 Like Reply Dec 22, 2015 #9 brontozaur Thread Starter All rights reserved Privacy Policy · Terms of Service · User Agreement

Video card information How to select a video card How to install a video card have a peek here

Available speeds 1x, 2x, 4x at 1.5V and 4x, 8x at 0.8V. AGP Connectors And Slots Each AGP card has one or two slots in its card edge. Generated Wed, 01 Feb 2017 11:24:19 GMT by s_wx1221 (squid/3.5.23) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.9/ Connection The system returned: (22) Invalid argument The remote host or network may be down.

Ati Tv Wonder Pro Windows 7

You may also come across the occasional motherboard which has an AGP universal connector covered by a sticker which says "do not insert 3.3 volt cards". I doubt it had any circuitry to prevent damage if you inserted a 3.3 volt card and there was no hint that you shouldn't insert one. Consumer-oriented video cards which need to draw lots of power usually require you to plug in a disk drive power supply cable. But AGP Pro video cards are rarely seen outside the workstation market because they aren't compatible with AGP motherboards.

Anyways I was thinking - 1) find all the grounds - these are probably all connected so resistance between them all should be very low? 2) find all the OUTPUTS - If I couldn't get either one, I'd try to recreate a portion of the circuit by following the traces. AGP Version Signaling Voltage Peak Speeds AGP 1.0 3.3 volts 1x at 267MB/s, 2x at 533MB/s AGP 2.0 1.5 volts 1x at 267MB/s, 2x at 533MB/s, 4x at 1067MB/s AGP 3.0 If a video card supports either 1.5 volt or 0.8 volt signaling then it has the 1.5 volt slot.

The most common is a motherboard BIOS incompatibility which prevents the motherboard from fully recognizing the video card. Sandra Lite can also give you very detailed information about your display adapter. It's a shame users have to be careful about this because if manufacturers obeyed the specification, it wouldn't be possible to make a mistake. You can also occasionally get memory resource conflicts by installing a new AGP video card into an old AGP 1.0 motherboard.

Majeed Ahmad Load More Your name or email address: Do you already have an account? Generated Wed, 01 Feb 2017 11:24:18 GMT by s_wx1221 (squid/3.5.23) An AGP card with both voltage slots can be plugged into any kind of AGP motherboard connector. But there are two pieces of information which they're missing: nobody makes AGP 3.0 cards, and nobody makes AGP 3.0 motherboards.

Ati Tv Wonder Software

It makes sense, if you think about it, because if anyone actually shipped a consumer-oriented product which supported only 0.8 volts, they would end up with lots of confused customers and AGP Multipliers AGP Version Signaling Voltage Possible Multipliers AGP 1.0 3.3 volts 1x, 2x AGP 2.0 1.5 volts 1x, 2x, 4x AGP 3.0 0.8 volts 4x, 8x AGP supports four different Ati Tv Wonder Pro Windows 7 Related Forum Posts: Need help figuring out what would be the increasing intervals. Wonder Pro Exercise The breakout cable is still with the card and may even have the documentation.

Do you have that one? Here are some links that may be helpful with tracking down the signals. Universal AGP 3.0 Motherboard Universal Supports 3.3V, 1.5V, and 0.8V signaling. I've seen plenty of video cards listed as "AGP 3.0 cards" when in fact they are actually universal 1.5V AGP 3.0 cards. Wonder Core

Sometimes manufacturers don't obey the rules. Available speeds 1x, 2x at 3.3V and 1x, 2x, 4x at 1.5V and 4x, 8x at 0.8V. Last edited by a moderator: Dec 22, 2015 #1 Like Reply Dec 20, 2015 #2 sailorjoe Member Jun 4, 2013 361 63 Hmmm, interesting problem. Check This Out The graphics chipset determines what kind of AGP card it is; not the brand of the video card.

I found the ATI card and cable. The system returned: (22) Invalid argument The remote host or network may be down. It's a place to start, but honestly it's tedious detailed work.Click to expand...

The system returned: (22) Invalid argument The remote host or network may be down.

Note the complete lack of "AGP 3.0 Card" entries. Here are some links that may be helpful with tracking down the signals. If you remove the 0.8 volt only entries from the compatibility table, then you end up with the following table. How would you go about this?

Should add> Odds are pretty good the cable is the same, my memory is telling me it has a large multi pin connector with all sorts of pigtails for video/audio in/0ut. If a video card has the 3.3 volt slot, then it can use 3.3 volt signaling. AGP 1.5V Card 1.5V slot Supports only 1.5V signaling. this contact form Available speeds 1x, 2x.

AGP 2.0 added the 1.5 volt slot on cards which could use 1.5 volt signaling. and Microchip Technology Inc. Every single video card I could find which claimed to be an AGP 3.0 card was actually a universal 1.5V AGP 3.0 card. Different manufacturers design differently.

If the card has both slots then it can use both signaling voltages. It has a different connector for the video/audio than your card. If I couldn't get either one, I'd try to recreate a portion of the circuit by following the traces. Check eBay, I bought four Osprey 210c's off eBay for $30.00 last year ($7.50 ea).

Your cache administrator is webmaster. Practical AGP Compatibility The previous table shows that there are combinations of motherboards and video cards which can be plugged together but do not work. By default, when the AGP 1.0 machine powers up it selects the fastest speed multiplier supported by both the video card and the motherboard. Otherwise they run at 1x which is always implemented by all AGP 1.0 video cards and motherboards.

The system returned: (22) Invalid argument The remote host or network may be down. AGP compatibility for sticklers: The Long Version AGP Basics In 1996, Intel introduced AGP 1.0. Once you try to install the driver, a memory conflict shows up. And every motherboard which claimed to be an AGP 3.0 motherboard turned out to be a universal 1.5V AGP 3.0 motherboard.

There may be some obscure product somewhere, but I sure can't find any. Please try the request again. Given the previous table, the confusion is understandable. Some low-end motherboards using AGP chipsets leave out the AGP connector to cut costs.